======================================== RangeLAN2 Windows 95/98/ME Drivers and Utilities v1.7 README.TXT file (c)2001 Proxim, Inc. ======================================== RANGELAN2 WINDOWS 95, WINDOWS 98, & WINDOWS MILLENNENIUM EDITION DRIVER VERSION 1.7-B21 The following README.TXT file details how to upgrade the RangeLAN2 Windows 95/98/ME driver from version 1.4B0 or 1.5B2 to version 1.7B21. **********************************IMPORTANT NOTE****************************************** Driver version 1.7-B21 supports only the following RangeLAN2 products: RangeLAN2 7421/22 PC Card RangeLAN2 7110 PCI Card This driver does not support the RangeLAN2 7401/02 PC Card, RangeLAN2 7100 ISA Card, or RangeLAN2 OEM Adapters. ****************************************************************************************** Section A describes how to upgrade the driver for RangeLAN2 7421 and 7422 PC Cards. Section B describes how to upgrade the driver for the RangeLAN2 7110 PCI Adapter. Section C contains troubleshooting instructions if you encounter a problem while upgrading the driver version. Section D describes how to uninstall driver version 1.7-B21. Section E describes how to contact Proxim Technical Support. SECTION A: UPGRADING THE RANGELAN2 7421/22 PC CARD Follow these steps to uninstall driver version 1.4B0 and install driver version 1.7B21: **********************************IMPORTANT NOTE****************************************** Driver version 1.7-B21 will install the RangeLAN2 7421/22 PC Card as a "HARMONY OPENAIR PC CARD." ****************************************************************************************** 1. Download the file RL2_958_1_7.EXE from Proxim's web site at http://www.proxim.com/support/ to a folder on your computer's hard drive. 2. Double-click RL2_958_1_7.EXE to extract the RangeLAN2 Windows 95/98/ME driver files. 3. Right-click the RangeLAN2 Status Monitor icon located in the Windows System Tray to launch the Status Monitor Information screen. Click to close the Status Monitor application. NOTE: If you are uninstalling a driver version earlier than 1.3-B5, remove the Status Monitor entry from the Add/Remove Programs icon in the Control Panel before proceeding to Step #4. 4. Remove the existing RangeLAN2 Card entry from either the Network Adapters category of the Device Manager or from the Network Configuration list in the Control Panel's Network icon. Do NOT restart the computer if prompted. 5. Remove the following files from the Windows directory, if present: C:\WINDOWS\INF\NETPROXM.INF C:\WINDOWS\INF\RL2API.INF C:\WINDOWS\SYSTEM\RL2API.VXD C:\WINDOWS\SYSTEM\RL2WIN95.SYS C:\WINDOWS\INF\OTHER\RangeLAN2NETPROXM.INF (on Windows 98/ME computers) C:\WINDOWS\START MENU\PROGRAMS\STARTUP\STATMON.LNK C:\PROGRAM FILES\RL2\*.* (Remove all files and folder) C:\START MENU\PROGRAMS\RL2\*.* (Remove all files and folder) NOTE: By default, Windows 95/98/ME will hide some of these file types. Confirm that you have configured Windows 95/98/ME to show all files before assuming that these files are not present. The "Hidden Files" option is available under the Folder Options heading of the Windows Explorer’s View or Tools Menu (depending on the operating system). 6. Shut Down the computer and remove the RangeLAN2 PC Card from the PCMCIA socket. 7. Turn on the computer. After the computer has been restarted, insert the RangeLAN2 PC Card into the PCMCIA socket, and the Detect New Hardware Wizard will automatically find the card. 8. For Windows ME, select "Specify the location of the driver (Advanced)" and enter the location of the driver files when prompted. For Windows 95/98, point the New Hardware Wizard to the folder containing the 1.7B21 driver files downloaded in Step #1 above. 9. Restart the computer when prompted. The RangeLAN2 Card should now function properly, and the OpenAir Utilities should also be installed (this assumes that the Windows directory is located on the C: drive). To confirm that the driver has been successfully updated, double-click the OpenAir Status Monitor in the Windows System Tray to launch the OpenAir Site Survey & Configuration Tool. The Site Survey & Configuration Tool should report the driver version as 1.7B21. 10. If you received an error message following the restart in Step #9 above, review the Troubleshooting suggestions in Section C below. Also, for additional assistance, refer to Chapters 3 and 8 of the Harmony 7430 Series OpenAir PC Card User's Guide, which is available for download on Proxim's Web site at http://www.proxim.com/support/. SECTION B: UPGRADING THE RANGELAN2 7110 PCI ADAPTER Follow these steps to uninstall driver version 1.5B2 and install driver version 1.7B21: 1. Download the file RL2WINME.EXE from Proxim's web site at http://www.proxim.com/support/ to a folder on your computer's hard drive. 2. Double-click RL2WINME.EXE to extract the RangeLAN2 Windows 95/98/ME driver files. 3. Right-click the RangeLAN2 Status Monitor icon located in the Windows System Tray to launch the Status Monitor Information screen. Click to close the Status Monitor application. 4. Remove the existing RangeLAN2 Card entry from either the Network Adapters category of the Device Manager or from the Network Configuration list in the Control Panel's Network icon. Do NOT restart the computer if prompted. 5. Remove the following files from the Windows directory, if present: C:\WINDOWS\INF\NETPROXM.INF C:\WINDOWS\INF\RL2API.INF C:\WINDOWS\SYSTEM\RL2API.VXD C:\WINDOWS\SYSTEM\RL2WIN95.SYS C:\WINDOWS\INF\OTHER\RangeLAN2NETPROXM.INF (on Windows 98/ME computers) C:\WINDOWS\START MENU\PROGRAMS\STARTUP\STATMON.LNK C:\PROGRAM FILES\RL2\*.* (Remove all files and folder) C:\START MENU\PROGRAMS\RL2\*.* (Remove all files and folder) NOTE: By default, Windows 95/98/ME will hide some of these file types. Confirm that you have configured Windows 95/98/ME to show all files before assuming that these files are not present. The "Hidden Files" option is available under the Folder Options heading of the Windows Explorer’s View or Tools Menu (depending on the operating system). 6. Shut Down the computer. 7. Turn on the computer. The Detect New Hardware Wizard will automatically find the card. 8. For Windows ME, select "Specify the location of the driver (Advanced)" and enter the location of the driver files when prompted. For Windows 95/98, point the New Hardware Wizard to the folder containing the 1.7B21 driver files downloaded in Step #1 above. 9. Restart the computer when prompted. The RangeLAN2 Card should now function properly, and the OpenAir Utilities should also be installed (this assumes that the Windows directory is located on the C: drive). To confirm that the driver has been successfully updated, double-click the OpenAir Status Monitor in the Windows System Tray to launch the OpenAir Site Survey & Configuration Tool. The Site Survey & Configuration Tool should report the driver version as 1.7B21. 10. If you received an error message following the restart in Step #9 above, review the Troubleshooting suggestions in Section C below. SECTION C: TROUBLESHOOTING SUGGESTIONS FOR WINDOWS 95/98/ME If you receive a DHCP (Dynamic Host Configuration Protocol) error message, then the RangeLAN2 Card has been properly installed in the computer. Contact your network administrator to determine if a DHCP resides on the network. If you have a DHCP server, confirm that the RangeLAN2 Card is synchronized to an Access Point on the network. If you do not have a DHCP server on the network, configure the RangeLAN2 Card with a valid IP address for the network from within the Control Panel's Network icon. If your network does not use TCP/IP to communicate, install the appropriate protocol for your network from within the Control Panel's Network icon. If you encounter a network adapter error or the OpenAir Status Monitor reports that the card is not working properly while trying to upgrade a RangeLAN2 Card to version 1.7B21, then follow the instructions below: 1. Open the Network icon and confirm that the following components appear in the Network Configuration list: Client for Microsoft Networks Proxim RangeLAN2 Card Adapter (or Harmony OpenAir PC Card) Proxim OpenAir Driver API TCP/IP If you have an additional network adapter (such as Dial-up adapter or a wired Ethernet card), your Network Configuration list may contain more entries. 2. If the Network Configuration list does not contain a RangeLAN2 or Harmony OpenAir entry, go to the Device Manager and see if the Proxim RangeLAN2 card has an entry under the Network adapters category. If not, check the Other Devices category to determine if it contains an entry for a "Proxim PC LAN Card" (for the PC Cards) or "PCI Network Controller" (for the PCI Adapter). If so, highlight and remove the Proxim PC LAN Card entry from the Device Manager. Once the entry has been removed, restart the computer and return to instructions above. 3. If you have a RangeLAN2 PC Card and it does not appear in either the Device Manager (Network Adapters or Other Devices categories) or within the Network Configuration list, open the PC Card icon in the Control Panel in order to confirm that the PCMCIA services recognizes that the RangeLAN2 PC Card is properly inserted in the PCMCIA slot. If you are using a RangeLAN2 7100 ISA Card and the RangeLAN2 card appears neither in the Device Manager (Network Adapters or Other Devices categories) or within the Network Configuration list, confirm that the ISA card is properly seated in an ISA slot on the computer's motherboard. 4. If the RangeLAN2 card is one of the entries in the Network Configuration list, go to the Network Adapters category of the Device Manager and find the entry labeled "Proxim RangeLAN2 Card" or "Harmony OpenAir PC Card." If the RangeLAN2 entry has an "!" next to it, the card probably has a resource conflict and is trying to use an Interrupt Level (IRQ), I/O Base Address, or Memory Range which is either already in use or not available for use by the card. NOTE: The RangeLAN2 PC Card uses an Interrupt Level, an I/O Base Address, and a Memory Range. The RangeLAN2 PCI Adapter uses one IRQ, at least one I/O Base Address, and one Memory Range. If you are using a RangeLAN2 PC Card, double-click the Device Manager entry to view the properties for the card. Click on the Resources tab to see what system resources the card is trying to use. Manually change the resource settings for the card to find available resources which the card can use. Click for these new settings to take effect; you may be prompted to restart the computer. After the computer restarts, the RangeLAN2 PC Card should function properly. NOTE: Typically, the Interrupt Level (IRQ) will be the cause of the resource conflict. You may find that your computer has no free Interrupt Level available for use. In this case, try setting the Interrupt Level to a value of 3 or 4 which generally corresponds to COM2 and COM3, respectively. If you are using a RangeLAN2 7110 PCI Adapter, a computer’s BIOS (Basic Input/Output System) automatically assigns resources to PCI cards during boot-up. The resources assigned to a PCI card cannot be changed within Windows 95/98/ME, only within the BIOS. If the PCI card has not been assigned an IRQ, check the PCI configuration settings within the BIOS Setup screen to assign the RangeLAN2 PCI Card available resources. If problems persist, contact the PC’s manufacturer to determine if an updated BIOS version is available that provides improved support for PCI devices. SECTION D: UNINSTALLING DRIVER VERSION 1.7-B21 Follow these steps to uninstall driver version 1.7B21: 1. Right-click the OpenAir Status Monitor icon located in the Windows System Tray to launch the Status Monitor Information screen. Click to close the Status Monitor application. 2. Remove the existing RangeLAN2 or Harmony OpenAir entry from either the Network Adapters category of the Device Manager or from the Network Configuration list in the Control Panel's Network icon. Do NOT restart the computer if prompted. 3. Remove the following files from the Windows directory, if present: C:\WINDOWS\INF\PRXWINME.INF C:\WINDOWS\INF\RL2API.INF C:\WINDOWS\INF\OTHER\RangeLAN2PRXWINME.INF C:\WINDOWS\SYSTEM\RL2API.VXD C:\WINDOWS\SYSTEM\RL2WIN95.SYS C:\WINDOWS\START MENU\PROGRAMS\STARTUP\STATMON.LNK C:\PROGRAM FILES\RL2\*.* (Remove all files in folder) C:\START MENU\PROGRAMS\RL2\*.* (Remove all files ) NOTE: By default, Windows 95/98/ME will hide some of these file types. Confirm that you have configured Windows 95/98/ME to show all files before assuming that these files are not present. The "Hidden Files" option is available under the Folder Options heading of the Windows Explorer’s View or Tools Menu (depending on the operating system). 4. Shut Down the computer. 5. Remove the RangeLAN2 adapter from the computer. SECTION E: HOW TO CONTACT PROXIM TECHNICAL SUPPORT You can reach Proxim Technical Support by voice, fax, e-mail, mail, or over the Internet: Tel: 800-477-6946 or 408-731-2640 Fax: 408-731-3676 Web: http://www.proxim.com/support/ e-mail: support@proxim.com Mail: Send correspondence to: Proxim, Inc. Attn: Proxim Technical Support 510 DeGuigne Drive Sunnyvale, CA 94085 ======================================== (c)2001 Proxim, Inc. ========================================